Is L9110S Dual DC Motor Driver Compatible with Home Assistant (ESPHome)?
Electrical Specifications
Always confirm pin assignments against the manufacturer datasheet before wiring.
Compatibility Overview
Dual-channel H-bridge DC motor driver for controlling small motor speed direction and linear actuators.
Wiring
Host connections for this device
Technical Specification Matrix
| Feature / Attribute | Specification / Status |
|---|---|
| Hardware Protocol | PWM GPIO / 5V-12V |
| Bridge Required | NO |
| Border Router Needed | None |
| Hardware Capabilities & Peripherals | Motor A Direction & Speed Motor B Speed Note: these entities come from the ESPHome configuration you flash — each one needs its matching component in that YAML before it appears. |
| Pairing Complexity | Intermediate |
| Factory Reset Instruction | Hold BOOT button for 3s. |
Wire, Flash, Adopt, Check
Wire it up
Follow the bus reference above. The host pins in the configuration are defaults — any free GPIO of the right kind will do, as long as the YAML names the pin you actually used.
Flash the configuration
Create a new device in the ESPHome dashboard (the Home Assistant add-on) and paste the configuration below into it, or save it as emb_esp32_l9110s_esphome.yaml and run esphome run emb_esp32_l9110s_esphome.yaml. The first flash goes over USB. If it is not detected, hold BOOT button for 3s to put it in download mode. Every update after that is over the air.
Adopt it in Home Assistant
Settings → Devices & Services. A node on the same network shows up as a discovered ESPHome device within a minute of joining Wi-Fi; choose Configure and enter the API encryption key from your secrets.yaml. If discovery does not find it, add the ESPHome integration by hand with the node's IP address.
Check it works
The entities on this page appear under the device in Home Assistant and update at the configured interval. The ESPHome log (Logs in the dashboard, or esphome logs) reports the setup of each component and any bus scan results at boot.
ESPHome Configuration
Starting configuration for L9110S Dual DC Motor Driver on ESP32. Untested on hardware — verify wiring and pins against your own board.
# ESPHome configuration for L9110S Dual DC Motor Driver
# Host: ESP32. Pin numbers below are host-side defaults — any free
# GPIO will do, and you should change them to match your own wiring.
esphome:
name: emb_esp32_l9110s_esphome
friendly_name: "L9110S Dual DC Motor Driver"
esp32:
board: esp32dev
framework:
type: esp-idf
logger:
api:
encryption:
key: !secret api_encryption_key
ota:
- platform: esphome
password: !secret ota_password
wifi:
ssid: !secret wifi_ssid
password: !secret wifi_password
# Each L9110S channel is an H-bridge with two inputs: PWM one and hold
# the other low for one direction, swap for the other. ESPHome's hbridge
# fan does that, with the fan's speed as the duty cycle and its direction
# as the polarity.
output:
- platform: ledc
pin: GPIO16
id: motor_a_1
- platform: ledc
pin: GPIO17
id: motor_a_2
- platform: ledc
pin: GPIO18
id: motor_b_1
- platform: ledc
pin: GPIO19
id: motor_b_2
fan:
- platform: hbridge
name: "Motor A"
pin_a: motor_a_1
pin_b: motor_a_2
- platform: hbridge
name: "Motor B"
pin_a: motor_b_1
pin_b: motor_b_2
Before you flash:
the !secret values come from your
secrets.yaml, and the GPIO numbers are host-side
defaults rather than properties of this part — change them to match how you actually wired it.
Report a Pinout Error or Submit Tested Code Snippets
Found a pin mapping quirk or built a custom ESPHome YAML driver for L9110S Dual DC Motor Driver? Submit a pull request or report corrections to our index.